Refractories

For All News & Features | To Subscribe to the RSS Feed

Results : 1 - 5 of 18

> CastExpo ‘10 Preview A week in the sun never sounded so good. For metalcasters enduring weak demand and idle production, the fresh ideas and technical insights upcoming at CastExpo will seem even more welcome than a few days of warm weather and relaxation.

> Molten Metal Splash and Furnace Refractory Safety (part 2) A sound refractory that has been properly installed, sintered and maintained, plus operator diligence to prevent a dangerous bridge from forming, are key to minimizing metal run-out. (The second of two parts.)

> Molten Metal Splash and Furnace Refractory Safety Molten metal splash is the most common cause of melt deck injuries and is caused by the addition of wet materials to the molten bath. It can be minimized by diligently inspecting and treating scrap. Metal run-out ranks among the most severe accidents that can occur during melting and holding. First of two parts.

> World's Largest Blast Furnace Starts 2,500 tons of Magneco/Metrel refractory line 5,500-m³ vessel

> Energy-saving Innovations for Furnaces, Delivery Vessels Tests show an increase in the melting capacity of gas-fired reverb furnaces using a dry hearth.

> CastExpo ‘10 Preview
A week in the sun never sounded so good. For metalcasters enduring weak demand and idle production, the fresh ideas and technical insights upcoming at CastExpo will seem even more welcome than a few days of warm weather and relaxation.

> Molten Metal Splash and Furnace Refractory Safety (part 2)
A sound refractory that has been properly installed, sintered and maintained, plus operator diligence to prevent a dangerous bridge from forming, are key to minimizing metal run-out. (The second of two parts.)

> Molten Metal Splash and Furnace Refractory Safety
Molten metal splash is the most common cause of melt deck injuries and is caused by the addition of wet materials to the molten bath. It can be minimized by diligently inspecting and treating scrap. Metal run-out ranks among the most severe accidents that can occur during melting and holding. First of two parts.

> World's Largest Blast Furnace Starts
2,500 tons of Magneco/Metrel refractory line 5,500-m³ vessel

> Energy-saving Innovations for Furnaces, Delivery Vessels
Tests show an increase in the melting capacity of gas-fired reverb furnaces using a dry hearth.

» More Refractories News & Features

For All Events | To Subscribe to the RSS Feed

Results : 1 - 1 of 1

Practical Metallurgy of Copper Based Casting Alloys
Internet Based Course

September 11, 2007

For All Products | To Submit a New Product

Results : 1 - 5 of 5

Biosoluable Insulation 07/01/08 THERMAL CERAMICS' Superwool Plus retains the advantage of exoneration from any carcinogen classification enjoyed by the standard Superwool 607, but has 30% more superior...
Ultra-Low Water Castable Refractories 02/01/07 ALLIED MINERAL PRODUCTS' V-CAST 700 series castables are a line of ultra-low water castables, designed for molten iron contact areas in channel furnaces, cupolas,...
Moldable Refractory 11/01/06 THERMAL CERAMICS Superfil 607 Moldable is a wet mastic material good for continuous use up to 2,000°F, with minimal shrinkage and high strength, even at high ...
Quick-Change Laminated Discs 11/01/06 ALLIED MINERALS line of Tuff-crete refractory products are low-cement castables specifically designed to be installed by shot-creting, but also can be pumped,...
Thermal Shock-Resistant Silica Composite 11/01/06 ZIRCAR REFRACTORY COMPOSITES refractory sheet type RSLE-57 is a low thermal expansion, high-strength reinforced silica matrix composite. Designed for use as a...

Biosoluable Insulation

07/01/08

THERMAL CERAMICS' Superwool Plus retains the advantage of exoneration from any carcinogen classification enjoyed by the standard Superwool 607, but has 30% more superior...

Ultra-Low Water Castable Refractories

02/01/07

ALLIED MINERAL PRODUCTS' V-CAST 700 series castables are a line of ultra-low water castables, designed for molten iron contact areas in channel furnaces, cupolas,...

Moldable Refractory

11/01/06

THERMAL CERAMICS Superfil 607 Moldable is a wet mastic material good for continuous use up to 2,000°F, with minimal shrinkage and high strength, even at high ...

Quick-Change Laminated Discs

11/01/06

ALLIED MINERALS line of Tuff-crete refractory products are low-cement castables specifically designed to be installed by shot-creting, but also can be pumped,...

Thermal Shock-Resistant Silica Composite

11/01/06

ZIRCAR REFRACTORY COMPOSITES refractory sheet type RSLE-57 is a low thermal expansion, high-strength reinforced silica matrix composite. Designed for use as a...

> Melting & Refractories